Track Roller Bearings & Cam Followers

Product Details:

The straightening of cables, strips and wires is performed in successive stages until the final product is obtained. During the drawing process, abnormal forces and stresses accumulate in the material as it is wound and stocked on reels or bobbins. For every production step, it is therefore necessary to carry out the inverse process by taking the material off its support and re-straightening/de-stressing it. It is at these moments that a quality straightener roller assembly is needed. The straightener assembly carries out three important functions:

Product Details:

The internal design of track rollers is the same as in single row or Double-rowAngular Contact Ball Bearings.The units can carry axial loads in both directions and, due to the thickness of the outer ring,large radial loads.

The standard product are produced from high quality bearing steel, with a hardness of 58 to62 HRC. Some types are also available in stainless steel (440C) with hardness 58 HRC.The track rollers contained in this catalogue are produced with standard tolerances (ISO 492)and standard clearance (CN).The track rollers are produced in two distinct families. Cylindrical or crowned outer ring andprofiled outer ring.NIKO1. Bearing materials

These track rollers are available in single and double row design. They are available withstraight cylindrical OD or crowned profile OD. The crowned OD is used to reduce the edgestresses caused by possible misalignment errors. The cylindrical OD can provide increasedsupport due to the longer contact profile.There products are used typically on flat surfaces.

The outer profile can have three different designs;-

Track rollers with gothic arch groove - type LFR- The track rollers RV have a groove machined in the outer ring. The groove is V shaped with an included angle of 120 degrees. These units are predominantly used on shafts with diameters from 7 to 20 MM. The contact between track roller and shafts is on two points. In special cases, the units can run on profiled ways. The units are supplied with non contact shields.

Track rollers with V shaped groove - type RV- The track rollers RV have a groove machined in the outer ring. The groove is V shapedwith an included angle of 120 degrees. These units are predominantly used on shafts with diameters from 7 to 20 MM. The contact between track roller and shafts is on two points. In special cases, the units can run on profiled ways. The units are supplied with non contact shields.
Track rollers with W profile - type RM The track rollers series RM have grooves machined in the outer ring of the unit with anincluded angle of 90 degree. They have been engineered to run on profiled steel elements that have identical shape. They can run on either the internal or the external surfaces of the outer ring. They are available with either non-contacting shields ZZ or contact seals 2RS.
Some of the most common applications are:-transfer rolls-idler rollers-Support rollers-Straightening rolls

Product Details:

Track rollers LFR are double row angular contact ball bearings comprising an outer ring with a gothic arch profile, an inner ring and two ball and cage assemblies with plastic cages. The inner ring and outer ring are made from rolling bearing steel
The special outer ring gives two point contact in the contact zone with the raceway. The contact angle α is a maximum of 30°. The bearings can support axial forces from both directions as well as radial forces

We have the Following in Ready Stock.

• LFR 50/5-4-KDD
• LFR 50/5-KDD
• LFR 50/8-KDD
• LFR 5201-12-KDD
• LFR 5201-10-KDD
• LFR 5301-KDD
• LFR 5302-KDD
• LFR 5204-16-KDD
• LFR 5206-16-KDD
• LFR 5206-25-KDD
• LFR 5207-30-KDD
• LFR 5208-40-KDD
• LFR 5308-50-KDD

Additional Information:

• Delivery Time: Ex-Stock

Product Details:

 Linear’s hardened crown rollers are a superb choice for low-cost linear motion. The rollers come pre-assembled and are self-aligning for simple installation. Hardened crown rollers are great for point-to-point applications, and ensure strong, sturdy and long-lasting linear motion. Hardened Crown Rollers are one of the least expensive bearing systems. NOTE: Rails, Wheels, End Stops, and Angle Brackets must be ordered as individual items below.

• Maximum wheel bearing load up to 1334 N (300 lbs)
• Maximum transfer speed up to 762 mm/s (30 in/s)
• Rails available up to 3 m (10 ft) in steel or powder coated finish
• Integral roller bearing with metric or inch threaded stud
• Available angle mounting brackets & rail end stops
• Ideal for machine tool doors and guarding
• Ideal for point to point material transfer
• Ideal for doors and windows – garage doors
• Ideal for many other general purpose applications

Product Details:

LV(V) Series Track Roller Bearings are with V groove profile, also called V groove profile trakc rollers, V guide wheels, are the structure of double row angular contact ball bearings, and have an extended outer ring, so the rollers can accommodate higher loads.
LV(V) Series Track Roller can be widely used in the cylindrical rail or ” V ” profile guide rail with an angle of 120 degrees.

They are widely used with the heavy-duty rails, mobile equipment, straightening machine and so on.

Product Details:

NRF & NRFE - Harhues & Teufert Brand

GUIDE ROLLERS WITH NEEDLE BEARINGS NFR / NFRE

Product Description

·         Make mounting holes for guide rollers according to dimension I H7 (H8).

·         Lock washer and nut are included in the scope of delivery.

·         Special castors in stainless steel design with suffixes. . . VA, e.g. NFR 22 VA.

·         Guide rollers are provided with a labyrinth seal on both sides.

·         Please inquire about heat-stabilized rolls.

·         Sb = possibility of lubrication on the thread side only from NFR / E 40.

·         * = in the transition phase, the NFR / E 110 can still be supplied with a slot.

Models:

Centric Type

• NFR 22
• NFR 32
• NFR 40
• NFR 52
• NFR 62
• NFR 72
• NFR 90
• NFR 110

Eccentric Type

• NFRE 22
• NFRE 32
• NFRE 40
• NFRE 52
• NFRE 62
• NFRE 72
• NFRE 90
• NFRE 110

Additional Information:

• Delivery Time: 4-6 Weeks, Subject to Prior Sale
• Packaging Details: Each

Product Details:

For reliable and dynamic linear motion, Bishop-Wisecarver’s innovative DualVee guide wheel design is unparalleled. This inspired ball bearing based guide wheels provides quiet, low friction motion in even the most extreme conditions. Coming in a diverse array of sizes, materials and complete with flexible mounting options, you are free to customize your system to your exact specifications and needs. Allow Bishop-Wisecarver to provide you Motion Without Limits with one of the many offerings from our DualVee Motion Technology product line.
BUY NOW

Product Details:

Heavy Duty Cam Followers and Roller Followers are follower bearings designed for outer ring rotation, and feature superior resistance against heavy loads and/or shock loads,incorporating full complements of cylindrical rollers in tworows in a thick walled outer ring.

The THK cam follower is a compact and highly rigid bearing complete with or without a shaft. It contains roller bearings and is used as a guide roller for cam mechanisms or linear motion.

With it's outer ring rotating whilst keeping contact with the mating surface - the cam follower is designed to bear an impact load.

For further information on our extensive range of THK cam followers, please contact our sales team.

Product Details:

We offer a range of Track Roller made using good quality metals and raw materials. They are highly suitable for withstanding medium to heavy rolling. Tested for performance and efficiency,these track rollers can be utilized in extreme conditions and are highly tolerant to cold, heat and dust. They offer easy installation and are simple to maintain.

Features:-

1. Available in different fittings and sizes
2. Suitable for multiple applications
3. Good quality of raw materials
4. Tested for resistance to corrosion
5. Bulk orders undertaken